XV Series Vertical Shaft Impact Crusher

    • XV

      Series

    • ≤30-50

      Sand Making Feed Size(mm)

    • ≤40-60

      Shaping Feed Size(mm)

    • 75-800

      Motor Power(kw)

    • 37-693

      Sand Making Throughput(t/h)

    • 42-785

      Shaping Throughput(t/h)

    Introduction

    Product Introduction

     

    XV series vertical shaft impact crusher absorbs many years of research and development experience and technical concept. It adopts new impeller design structure and special sealing structure to prevent the oil leakage of the bearing cylinder. It has the characteristics of energy saving, long service life and wide application. It is widely used in the processing of fine-grained aggregates and artificial sand in stone production; metal and non-metal mines are used to replace the fine crushing operation of traditional crush crushers; cement production is used for pre-grinding operations in the grinding process and can greatly reduce energy consumption; crushing glass in the recycling industry.

     

    Working Principle

     

    The materials fall into impeller with high-speed rotation vertically. On the force of high-speed centrifugal, the materials strike to the other part of material in a high speed. After mutual impacting, the materials will strike and rub between the impeller and the casing and then be discharged straight from the lower portion to form a closed multiple cycles. Final product is controlled by screening equipment to meet the requirement. The XV series vertical impact crushers has two types: rock-on-rock and rock-on-iron. Rock-on rock is to process abrasive material and rock-on –iron is to process normal material. The production of rock-on-iron is 10-20% higher than rock-on-rock.

     

    配图1.3.jpg

     

    Product Features & Advantages

     

    1. Based on the high-speed impact crushing mechanism, the product has excellent grain shape, is cubic, and has a low needle-like content; therefore, it is especially suitable for aggregate shaping and artificial sand making, such as the production and processing of aggregates for expressways;
    2. The impeller structure adopts a new structural design, and the material throughput is increased by about 30%.
    3. Adopting the “rock-on-rock” working mode to reduce the types of wear-resistant use and reduce the production cost of the customer; the structure and process of the impeller are adjusted, and the service life of the impeller is greatly improved compared with the previous equipment under the same material;
    4. Waterfall feeding technology can not only improve energy utilization rate, increase production, but also regulate product grain shape and control product powder content through waterfall feeding;
    5. Adopting thin oil lubrication system, special sealing structure prevents oil leakage of bearing cylinder and reduces failure of transmission system;
    6. Equipped with hydraulic lifting device can helps customer easy maintenance and labor saving.

     

     

    Parameters

     

    Model

    Sand Making

    Shaping

    Sand Making

    Shaping

    Rotor Speed(r/min)

    Motor Power
    (kw)

    Feed Size(mm)

    Thoroughput(t/h)

    XV311D

    ≤30

    ≤40

    37-63

    42-71

    1300-1700

    75

    46-78

    52-83

    90

    55-96

    62-103

    110

    XV311

    ≤30

    ≤40

    82-132

    113-144

    1300-1700

    75×2

    109-155

    131-175

    90×2

    135-200

    175-215

    110×2

    XV371

    ≤35

    ≤45

    157-225

    183-255

    1200-1500

    132×2

    186-268

    246-315

    160×2

    236-305

    324-373

    200×2

    XV431

    ≤45

    ≤55

    265-355

    342-396

    1000-1260

    220×2

    304-388

    386-442

    250×2

    XV491

    ≤50

    ≤60

    446-526

    545-587

    900-1160

    315×2

    485-693

    590-785

    400×2

    Note:

    1. The processing capacity is the data when the density of the broken material is 1.6×103 kg/m3. The production capacity is related to the physical properties of the crushed material, the feeding mode, the feeding granularity and its composition;

    2. Our products are constantly updated and improved, we reserves the right to change parameters and design without first notifying the user;

    3. The above product configuration is not necessarily the factory standard configuration. Please consult us in detail when purchasing.